Operating and installation instructions
Refrigerator with Dynamic cooling
K 12421 SD
en - GB
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 09 290 820
Contents
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning the interior and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Appliance door, side panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Ventilation gaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Metal grille at the back of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
After Sales / Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Information for dealers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Demo mode r. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Climate range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Changing the door hinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Aligning the appliance door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Building in the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3
Guide to the appliance
aOn/Off button
dMenu symbol
(Setting mode for the brightness
level of the display)
bSuper cool button
cDisplay
eSuper cool symbol
If the appliance is not operated for
some time, the display will revert
automatically to the brightness level
which has been set.
As soon as a button is pressed the
display will light up at the brightest
setting.
fTemperature display
gTemperature selector button
hDynamic cooling button
iDynamic cooling symbol
jBrightness symbol
4
Guide to the appliance
aControl panel
bDynamic cooling fan
cButter and cheese compartment
dEgg tray
eAdjustable shelves
fBottle rack
gBottle shelf
hCondensate channel and
drain hole
iFruit and vegetable containers
5
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Take care not to damage the pipework
at the back of it before or during
transportation to an authorised
collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained, and will not leak out into the
environment.
6
Warning and Safety instructions
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
This appliance complies with all
relevant safety requirements.
Improper use can, however, present
a risk of both personal injury and
material damage.
for damage resulting from incorrect or
improper use or operation of the
appliance.
The appliance can only be used by
people with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, if they are
supervised whilst using it, or have been
shown how to use it in a safe way and
understand the hazards involved.
~
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before installation and before using
it for the first time. They contain
important notes on installation,
safety, operation and maintenance.
Safety with children
Keep these instructions in a safe
place and pass them on to any
future user.
Children 8 years and older may use
~
the appliance only if they have been
shown how to use it in a safe way and
understand the hazards involved.
Correct application
Children under 8 years of age must
be kept away from the appliance unless
they are constantly supervised.
This appliance is not designed for
~
~
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
This appliance is not a toy! Do not
~
allow children to play with it or near it,
or to play with the controls. Do not let
them swing on the door.
– Shops
– Offices and showrooms
and by residents in establishments
such as:
– Hostels and guest houses.
The appliance is not intended for
outdoor use.
It must only be used as a domestic
appliance to cool and store foodstuffs.
7
Warning and Safety instructions
Technical safety
The more coolant there is in an
appliance, the larger the room it should
be installed in. In the event of a
leakage, if the appliance is in a small
room, there is the danger of
combustible gases building up.
For every 8 g of coolant at least 1 m3 of
room space is required. The amount of
coolant in the appliance is stated on the
data plate inside the appliance.
~
Before setting up the appliance,
~
check it for any externally visible
damage. Do not install and use a
damaged appliance.
It could be dangerous.
If the connection cable is faulty it
~
must only be replaced by a service
technician authorised by the
manufacturer to protect the user from
danger.
Safe operation of the appliance is
~
only assured if it has been installed and
connected in accordance with these
This appliance contains the coolant
Isobutane (R600a), a natural gas which operating and installation instructions.
is environmentally friendly. Although it
~
Before connecting the appliance,
~
is flammable, it does not damage the
check that the connection data on the
ozone layer and does not increase the
data plate (voltage and connected
greenhouse effect. The use of this
load) match the mains electricity
coolant has, however, led to a slight
supply,
increase in the noise level of the
This data must correspond in order to
appliance. In addition to the noise of
avoid the risk of damage to the
the compressor, you might be able to
appliance. Consult a qualified
hear the coolant flowing around the
electrician if in any doubt.
system. This is unavoidable, but does
not have any adverse effect on the
performance of the appliance. Care
must be taken during transportation
and setting up of the appliance that no
parts of the cooling system are
damaged. Leaking coolant can
damage the eyes.
Do not connect the appliance to the
mains electricity supply by a
multi-socket adapter or an extension
lead. These do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
~
In the event of any damage:
- avoid open flames and anything which
creates a spark,
- disconnect from the mains,
- air the room in which the appliance is
located for several minutes and
- contact the Service Department for
advice.
8
Warning and Safety instructions
The electrical safety of this
The appliance must be isolated from
the electricity supply during installation,
maintenance and repair work.
~
~
appliance can only be guaranteed if
correctly earthed. It is most important
that this basic safety requirement is
observed and regularly tested and
where there is any doubt, the
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for damage or injury caused by the lack
of or inadequacy of an effective
Faulty components must only be
~
replaced by genuine Miele original
spare parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
This appliance must not be used in
~
a non-stationary location (e.g. on a
ship).
earthing system (e.g. electric shock).
Installation, maintenance and
~
repairs may only be carried out by a
suitably qualified and competent
person in strict accordance with current vermin, pay particular attention to
In areas which may be subject to
~
infestation by cockroaches or other
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
keeping the appliance in a clean
condition at all times. Any damage
which may be caused by cockroaches
or other vermin will not be covered by
the guarantee.
While the appliance is under
~
guarantee, repairs should only be
undertaken by a service technician
authorised by the manufacturer.
Otherwise the guarantee will be
invalidated.
9
Warning and Safety instructions
Correct use
build-up of gases and pose a danger to
health.
Do not store explosive materials in
~
the appliance or any products
containing propellants (e.g. spray
cans). Thermostats switching on may
produce sparks which could present a
fire hazard. Flammable compounds
could explode.
Do not use a steam-cleaning
appliance to clean this appliance.
~
Steam could reach the electrical
components and cause a short circuit.
Do not use any oils or grease on the
~
door seals, as these will cause the
seals to deteriorate and become
porous with time.
Do not operate any electrical
~
equipment (e.g. an electric ice-cream
maker) inside the appliance. Danger of
sparking and explosion.
If storing food which contains a lot of
~
fat or oil, make sure that it does not
come into contact with plastic
components as this could cause stress
cracks.
If storing alcohol with a high
~
percentage proof in the refrigerator,
make sure the bottle is tightly closed
and stored upright. Danger of
explosion.
Do not block the ventilation gaps in
~
the appliance as this would impair the
Observe the "use by" dates given on efficiency of the appliance, increase the
food to avoid the risk of food poisoning. electricity consumption and could
~
Storage times will depend on several
factors, including the freshness and
quality of the food as well as the
temperature at which it is stored. Follow
the instructions given on food
manufacturer's packaging on storage
conditions required, as well as the "use
by" date.
cause damage to the appliance.
The appliance is designed for use
~
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range
for your appliance is stated on the data
plate inside the appliance.
Installing it in a room with too low an
ambient temperature, e.g. a garage,
will lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
Do not use sharp edged objects to
~
– remove frost and ice,
– separate food which has become
frozen.
They will damage the evaporator,
causing irreversible damage to the
appliance.
Do not use defrosting sprays or
de-icers, as they might contain
~
substances which could damage the
plastic parts or which could cause a
10
Warning and Safety instructions
Disposal of your old appliance
Before disposing of an old
appliance, first make the door latch or
lock unusable.
~
This way you will prevent children from
accidentally locking themselves in and
endangering their lives.
Be careful not to damage any part of
~
the pipework whilst awaiting disposal,
e.g. by
– puncturing the refrigerant channels
in the evaporator.
– bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
11
How to save energy
Normal energy
consumption
Increased energy
consumption
Installation site
In a ventilated room.
In an enclosed, unventilated room.
In direct sunlight.
Protected from direct sunlight.
Not near to a heat source (radiator, Near to a heat source (radiator,
oven).
oven).
Where the ideal ambient room
temperature is approx. 20°C.
Where there is a high ambient room
temperature.
Do not cover the ventilation gaps
and dust them regularly.
Temperature setting
with a thermostat
which is approximate
(set in stages).
With a medium setting of 2 to 3.
With a high setting: the lower the
temperature in the compartment, the
higher the energy consumption.
Temperature setting
with a thermostat which
is exact to the degree
(digital display).
Larder section 8 to 12 °C
On appliances with winter setting,
please make sure that the winter
setting is switched off when the
ambient temperature is warmer than
16 °C .
Refrigerator section 4 to 5 °C
PerfectFresh zone just above 0 °C
Freezer section -18 °C
Wine storage section 10 to 12 °C
Use
Drawers, shelves and racks
arranged as they were when the
appliance was delivered.
Only open the door when necessary Frequent opening of the door for
and for as short a time as possible. long periods will cause a loss of
coldness.
Store food in an organised way.
Searching for an item will mean the
door is open for longer.
Allow hot food and drinks to cool
down before placing them in the
appliance.
Hot food will cause the compressor
to run for a long time, as the
appliance will have to work harder
to reduce the temperature.
Store food covered or packaged.
The evaporation or condensation of
liquids will cause a loss of coldness
in the refrigerator.
Place frozen food in the refrigerator
to defrost.
Do not over-fill the appliance to
allow air to circulate.
Defrosting
Defrost the freezer section when a A layer of ice hinders the cold from
layer of ice 0.5 cm thick (maximum) reaching the frozen food, and
has built up.
increases energy consumption.
12
Switching on and off
Before using for the first time
Switching off
Protective foil
The stainless steel trim in the interior
has a layer of protective foil to prevent
damage during transportation.
On stainless steel appliances, there will
also be protective foil on the stainless
steel door and on some appliances on
the side panels as well.
^ Press the On/Off button until the
display goes out.
The cooling system is switched off.
Switching off for longer
periods of time
^ Do not remove the foil until the
appliance has been positioned in its
final location.
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
Cleaning
^ switch the appliance off,
^ disconnect it from the mains,
^ clean the appliance out and
^ leave the door ajar to air it.
^ Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing-up liquid, and
then dry with a soft cloth.
Switching on
If, during a long absence, the
appliance is switched off but not
cleaned out and the door is left shut,
there is a danger of mould and
odours building up inside the
appliance.
^ Press the On/Off button.
The appliance will start to cool and the
temperature required will appear in the
temperature display. The interior
lighting will come on when the door is
opened.
13
Customising settings
Settings mode X
You can alter the brightness of the
display s in Settings mode.
Settings mode is represented in the
display by the Menu symbol X. The
following section describes how to
access Settings mode and alter
settings.
^ Press the Temperature button
repeatedly until the brightness level
required is reached.
The more areas of the temperature
display which light up, the brighter
the display.
Altering the brightness of the display
To confirm the altered setting:
The display brightness can be adjusted
to suit the lighting conditions of the
room.
There are five different display
brightness settings. The factory default
setting is 1.
^ Press the Super cool button briefly.
The Brightness symbol s will flash.
The newly selected setting has been
saved.
To come out of Settings mode:
^ Press the Super cool button for
approx. five seconds.
The Menu symbol X will light up,
settings mode is now activated. The
Brightness symbol s will start
flashing.
^ Press the On/Off button.
or
^ Wait for 5 minutes.
The Menu and Brightness symbols
will go out.
The temperature display will show
the required temperature.
^ Press the Super cool button briefly to
confirm this.
The Brightness symbol s will light
up.
14
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
. . . in the refrigerator
We recommend a temperature of 5 °C
in the middle of the refrigerator.
Setting the temperature
The temperature in the appliance will
rise:
^ Press the temperature selector button
repeatedly until the indicator light for
the temperature you want lights up in
the display.
– the more often the door is opened
and the longer it is kept open,
– the more food that is placed in it,
The first time you press the button the
indicator light for the last temperature
you set will flash in the display.
– the warmer the food is which is being
put into it,
– the higher the ambient temperature
surrounding the appliance.
The temperature value will change up
until the setting for 9 °C is reached. It
will then drop back to the 1 °C setting.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
The newly selected temperature will be
adopted automatically after a short
while.
The indicator for the temperature which
has been set for the refrigerator will
light up constantly.
The temperature can be set slightly
colder than shown in the display if
wished.
The following example shows how this
option works:
15
The correct temperature
To set the temperature between 5 and
7 °C to be slightly colder:
Temperature display
The temperature display on the
control panel always shows the
required temperature.
^ Press the temperature selector button
repeatedly until the indicator for 5 °C
lights up.
The temperature can be adjusted from
1 °C to 9 °C.
^ Press the button for approx. another
5 seconds to set the temperature.
The colder temperature setting within
the small temperature range is now set.
However, this is not visible in the
temperature display.
16
Super cool and Dynamic cooling
Super cool
Dynamic cooling
The Super cool function can be used to When the Dynamic cooling function is
rapidly reduce the temperature in the
refrigerator to its lowest setting
(depending on the room temperature).
not switched on, the natural circulation
of air in the appliance will cause
different temperature zones in the
refrigerator as the cold, heavy air will
sink to the lowest section of the
Switching on Super cool
appliance. You should bear this in mind
when placing food in the appliance
(see "Using the refrigerator efficiently").
However, if you are placing a large
amount of food in the refrigerator at any
one time, it is a good idea to switch on
Dynamic cooling. This way you can
distribute the temperature inside the
appliance to all areas more evenly so
that all the food will be chilled to about
the same degree.
Super cool is particularly
recommended for the faster chilling of
large amounts of fresh food or drink.
^ Press the Super cool button.
The Super cool symbol ª will light
up. The appliance will work at full
power to lower the temperature in the
appliance.
The temperature is set as normal with
the Temperature button.
Dynamic cooling should also be
selected when:
Switching off Super cool
– the ambient temperature in the room
is high (above approx. 30 °C), and
The Super cool function will switch itself
off automatically after approx. 6 - 12
hours. The Super cool ª symbol will go
out and the appliance will run at normal
power again.
– the room humidity level is high (e.g.
during summer).
To save energy, the Super cool function
can be switched off once food and
drinks are sufficiently chilled.
^ Press the Super cool button. The
Super cool symbol ª will go out.
17
Super cool and Dynamic cooling
Switching on Dynamic cooling
^ Press the Dynamic cooling button.
The Dynamic cooling symbol ¢ will
light up.
The Dynamic cooling fan is now
ready to operate. It will switch on
automatically when the compressor
switches on.
Switching off Dynamic cooling
^ Press the Dynamic cooling button.
The Dynamic cooling symbol will go
out.
To save energy, the Dynamic
cooling fan switches off
automatically whilst the door is
open.
18
Using the refrigerator efficiently
Different storage zones
should be kept at a temperature of
approx. 4 °C.
Due to the natural circulation of the air
in the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
the different zones when placing food
in the appliance.
Do not store explosive materials in
the appliance or any products
containing propellants (e.g. spray
cans). Danger of explosion.
This appliance has dynamic cooling,
which helps to keep an even
temperature when the fan is running.
When Dynamic cooling is switched
on, the difference between the
various zones less pronounced.
If storing alcohol with a high
percentage proof, make sure it is
tightly closed, and store upright.
Please be aware if storing cooking
oil in the appliance that traces of oil
can cause stress cracks to occur in
plastic components.
Warmest area
The warmest area is in the top section
of the door. Use this for storing butter
and cheese.
Food must not touch the back wall of
the appliance, as it may freeze to
the back wall.
Coldest area
The coldest area in a refrigerator is
directly above the vegetable containers
and at the back wall.
To allow air to circulate efficiently,
do not pack food too closely
together in the refrigerator. Do not
cover the fan in the rear wall of the
refrigerator, as this is essential for
keeping the appliance cool.
Use this for all delicate and highly
perishable food, e.g.
– fish, meat, poultry,
– sausage products, ready meals,
– dishes or baked goods containing
eggs or cream,
– fresh dough, cake mixtures, pizza or
quiche dough,
– soft cheese and other dairy
products,
– pre-packed vegetables and other
fresh food with a label stating it
19
Using the refrigerator efficiently
Food which is not suitable for
storing in the refrigerator
Storing food correctly
Store food covered or packaged. This
will prevent food smells from affecting
other food, food from drying out, and
also any cross-contamination of
bacteria. The growth of bacteria, such
as salmonella, can be avoided by
setting the correct temperature and
maintaining good standards of hygiene.
Not all food is suitable for storing in a
refrigerator at temperatures below 5 °C,
as some food does not tolerate cold
temperatures. Cucumbers, for example,
become glassy, aubergines bitter and
potatoes sweet. Tomatoes and oranges
loose their aroma, and the peel on
citrus fruits hardens.
Fruit and vegetables
Food which does not tolerate cold
temperatures includes:
Fruit and vegetables may be stored
loose in the vegetable containers.
However, please bear in mind that not
all types of fruit and vegetables are
suitable for storing in the same
– Pineapple, avocado, bananas,
pomegranate, mango, melon,
papaya, passion fruit,
citrus fruit (such as lemons, oranges,
mandarins, grapefruit),
container. Aromas and flavours can
transfer from one type of food to
another (e.g. carrots absorb the smell
and flavour of onions very easily). Some
food also gives off a natural gas
(ethylene) which speeds up the rate at
which other food perishes. Some fruit
and vegetables react strongly to this
gas and should not be stored together.
– Fruit which is not yet ripe,
– Aubergines/egg plant, cucumber,
potatoes, peppers/capiscum,
tomatoes, courgettes/zucchini,
– Some hard cheeses, e.g. Parmesan.
When shopping for food
Examples of fruit and vegetables
which produce a large amount of this
natural gas are:
The freshness of food when first placed
in the appliance is an important factor in
determining how long it stays fresh.
Time out of the refrigerator, e.g. during
transportation, should be kept to a
minimum. For example, do not allow
food to stay in a hot car for too long.
Once food has started to deteriorate,
this process cannot be reversed. As little
as two hours outside the refrigerator can
cause food to start deteriorating.
Apples, apricots, pears, nectarines,
peaches, plums, avocados, figs,
blueberries, melons and beans.
20
Using the refrigerator efficiently
Examples of fruit and vegetables
which react strongly to the natural
gases given off by other types of fruit
and vegetables are:
Meat
Meat should be stored unwrapped.
(Undo wrappings slightly to leave meat
loosely covered, and leave containers
open). This permits air to circulate
around the meat, allowing the surface
to dry slightly, which helps prevent the
growth of bacteria. To prevent the risk
of bacterial cross-contamination and
meat deteriorating, do not let one type
of meat come into direct contact with
another type.
Kiwis, broccoli, cauliflower, Brussels
sprouts, mangos, honeydew melons,
apples, apricots, cucumbers, tomatoes,
pears, nectarines and peaches.
Example: Broccoli should not be stored
with apples, as apples produce a large
amount of natural gas to which broccoli
is very sensitive. The result is a shorter
than expected storage time for the
broccoli.
Unpacked meat and vegetables
Unpackaged meat and vegetables
should be stored separately. To avoid
any microbiological
cross-contamination, these foods may
only be stored together if they are
wrapped.
Protein rich foods
Please note that foods rich in protein
deteriorate faster than others.
Shellfish, for example, deteriorates
faster than fish, and fish deteriorates
faster than meat.
21
Adjusting the interior fittings
Moving the shelves
The shelves can be adjusted according
to the height of the food.
^ Raise the shelf, and pull it forwards
slightly until the notch at the side is in
line with the shelf support. It can then
be raised or lowered to the required
level.
^ fit the two brackets onto the supports
on either side at the required height,
The raised edge at the back must face
upwards to prevent food from touching
the back of the appliance and freezing
to it.
^ and push the glass shelves in one
after the other.
The shelf with the raised edge must
be at the back.
Stoppers prevent the shelves from
being dislodged by mistake.
Adjusting the door shelf/bottle
shelf
Split shelf
In order to accommodate tall items in
the appliance, one of the shelves is
divided. The front section can be
pushed under the rear section.
^ Push the door/bottle shelf upwards,
then remove it by pulling it forwards.
^ Replace the door/bottle shelf at the
required position. Ensure that it is
securely pushed back into position.
^ Push the rear half of the glass shelf
up slightly from below.
^ At the same time, pull the front half of
the glass shelf forwards slightly and
then push it carefully under the rear
half.
To move the split shelf:
^ Take both halves of the split glass
shelf out,
22
Automatic defrost
The refrigerator defrosts automatically.
Condensate and frost can build up on
the back wall of the refrigerator whilst it
is in use. You do not need to remove
this, as it will defrost and evaporate
automatically with the warmth
generated by the appliance.
The condensate is drained away via a
channel and drain hole into an
evaporation system at the back of the
appliance.
Ensure that the condensate channel
and drain hole are kept clean and
are never blocked so that
condensate can flow away without
hindrance.
23
Cleaning and care
A range of Miele branded cleaning and – hard, abrasive sponges and
conditioning products is available to
order from Miele or from
brushes, e.g. pot scourers,
– melamine eraser blocks,
– sharp metal scrapers.
Make sure that water cannot
penetrate into the electronic unit or
into the light.
Before cleaning
^ Switch the appliance off.
Do not let water get into the
condensate channel and drain hole
when cleaning.
^ Disconnect the appliance from the
mains.
^ Take any food out of the appliance
and store it in a cool place.
Do not use steam cleaning
apparatus to clean the appliance.
Steam could reach electrical
components and cause a short
circuit.
^ Take out any removable parts, e.g.
shelves, for cleaning.
Cleaning the interior and
accessories
The data plate located inside the
appliance must not be removed.
It contains information which is
required in the event of a service call.
^ Clean the appliance at least once a
month.
Remove soiling immediately to
prevent it from drying on.
To avoid damaging the surface of
your appliance, do not use:
Use lukewarm water with a little
washing-up liquid.
– cleaning agents containing soda,
ammonia, acids or chlorides,
The following are dishwasher safe:
– cleaning agents containing
descaling agents,
– the butter dish, egg trays
(supplied as standard, depending on
model)
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
– the shelves and bottle shelf in the
door
– solvent-based cleaning agents,
– stainless steel cleaning agents,
– dishwasher cleaner,
– the butter and cheese compartment
– oven sprays,
– glass cleaning agents,
24
Cleaning and care
Appliance door, side panels
The temperature of the dishwasher
programme must not exceed 55 °C.
Contact with some foodstuffs, such
as carrots, tomatoes or ketchup can
cause plastic items to discolour.
However, this discolouration will not
affect the stability of plastic items.
Remove any soiling from the
appliance door and side panels im-
mediately.
If this is not done, it might become
impossible to remove and could
cause the surface to alter or
discolour.
^ Clean the interior shelves and
drawers by hand. These are not
suitable for cleaning in a dishwasher.
All surfaces are susceptible to
scratching.
Contact with unsuitable cleaning
agents can alter or discolour the
surfaces.
^ Clean the condensate channel and
drain hole frequently, so that
condensate can drain away
unhindered. Use a straw or similar to
clear the drain if necessary.
^ The surfaces should be cleaned
using a solution of hot water and a
little washing-up liquid applied with a
soft sponge. They can also be
^ After cleaning, wipe the interior and
accessories with a damp cloth and
dry with a soft cloth.
Leave the door open to air the
appliance for a short while.
cleaned with a damp microfibre cloth
(without using any cleaning agent).
^ After cleaning, wipe with a clean
water and dry with a soft cloth.
25
Cleaning and care
Ventilation gaps
After cleaning
^ The ventilation gaps should be
cleaned regularly with a brush or
vacuum cleaner. A build-up of dust
will increase the energy consumption
of the appliance.
^ Replace all shelves and accessories
in the appliance.
^ Reconnect to the mains and switch
the appliance back on.
^ Place food back in the appliance and
close the door.
Door seal
Do not use any oils or grease on the
door seal as these will cause the
seal to deteriorate and become
porous over time.
The door seal should be cleaned
regularly with clean water and then
wiped dry with a soft cloth.
Metal grille at the back of the
appliance
The metal grille at the back of the
appliance (heat exchanger) should be
dusted at least once a year. A build-up
of dust will increase the energy
consumption of the appliance.
When cleaning the grille, make sure
that the pipework and other
components do not get broken or
damaged in any way.
26
Problem solving guide
Some minor problems can be corrected without contacting Miele.
If having followed the suggestions below, you still cannot remedy the fault, please
contact Miele. To prevent unnecessary loss of temperature it is advisable not to
open the door while waiting for the appliance to be serviced.
Installation, maintenance and repairs may only be carried out by a suitably
qualified and competent person in strict accordance with current national and
local safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
Problem
Possible cause
Remedy
The appliance does The appliance has not been
not heat up.
^ Press the On/Off
button.
switched on. The temperature
display is not lit up.
The plug is not inserted in the
socket correctly.
^ Insert the plug in the
socket correctly.
Check whether the mains fuse
has tripped. There could be a
fault with the appliance, the
household electrical wiring or
another electrical appliance.
^ Contact a qualified
electrician or Miele.
The temperature
inside the appliance
is too low.
^ Set a warmer
temperature.
The Super cool function is still
switched on. The Super cool
function switches itself off
automatically after approx. 6 -
12 hours.
You can switch off the
Super cool function
earlier to save energy.
^ Press the Super cool
button.
27
Problem solving guide
Problem
Possible cause
Remedy
The appliance is
switching in too
frequently or for too become dusty.
The ventilation gaps have
been covered over or
^ Do not cover or block the
ventilation gaps.
^ Dust the ventilation gaps
and the heat exchanger
regularly.
long.
The metal grille (heat
exchanger) at the rear of the
appliance has become
dusty.
The door has been opened Only open the door when
too frequently, or a large
amount of food has been
put in at once.
necessary and for as short
a time as possible.
The required temperature
will re-establish itself after a
while.
^ See "The correct
temperature" for more
information.
The door cannot be closed
correctly.
The ambient temperature is ^ See "Installation -
Location" for more
information.
too high.
The higher the ambient
temperature, the longer the
compressor will run for.
28
Problem solving guide
Problem
Possible cause
Remedy
The appliance is
switching in too
frequently or for too speed, but for longer, when
To save energy, the
compressor runs at a lower
long.
less cooling is required.
The Super cool function is
still switched on.
The Super cool function
switches itself off
automatically after approx. 6
- 12 hours. You can switch
off the Super cool function
earlier to save energy.
^ Press the Super cool
button.
The r symbol lights Demo mode has been
^ Deactivate Demo mode
(see "Information for
dealers - Demo mode").
up.
activated. This allows the
appliance to be displayed
in the showroom without the
cooling system being
switched on. Do not activate
this setting for domestic
use!
29
Problem solving guide
Problem
Possible cause
Remedy
The interior lighting The lighting switches itself ^ Disconnect the appliance
from the mains.
is not working.
off automatically after
approx. 15 minutes if the
door is left open.
If it does not come on when
the door is opened briefly,
but the temperature display
is working, then the lighting
is defective.
^ Press the sides of the
lamp cover forwards (1)
and unhook the cover (2).
^ Unscrew the lamp and
replace it with a new one.
Lamp specification:
220 - 240 V, E 14 cap
See the old lamp for the
Wattage required.
^ Replace the cover by
clipping it in at the rear
and then pressing it in at
the sides.
The floor of the
refrigerator is wet.
The condensate drain hole ^ Clean the condensate
channel and drain hole.
is blocked.
30
Noises
Normal noises
Brrrrr...
What causes them
Humming noise made by the motor (compressor). This noise
can get louder for brief periods when the motor is switching on.
Blubb, blubb.... A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....
Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....
Creak ...
On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you Possible cause
can easily
rectify
Remedy
Rattling,
vibrating
The appliance is uneven.
Realign the appliance using
a spirit level, by raising or
lowering the screw feet
underneath the appliance.
The appliance is touching
another appliance or piece of
furniture.
Move it away.
Drawers, baskets or shelves
are unstable or sticking.
Check all removable items
and refit them correctly.
Are any bottles or containers Separate them.
unstable or knocking against
each other?
The transport cable clips are Remove the clips.
hanging loose at the back of
the appliance.
31
After Sales / Guarantee
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– your Miele Dealer
or
– Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. However, you must activate
your cover by calling 0845 365 6640 or
32
Information for dealers
Demo mode r
To deactivate Demo mode
The appliance can be demonstrated in
the showroom or at exhibitions in
"Demo mode". In this mode the interior
lighting, the display and the controls
are functioning but the compressor
remains switched off.
^ Press the On/Off button and the
Temperature button at the same time
for approx. 5 seconds.
The Menu symbol X, the Super cool
symbol ª and the 3 ° C area of the
temperature display will flash.
Demo mode is represented in the
display by the r symbol.
^ Press the Super cool button.
The r symbol will go out and the area of
the temperature set will light up or flash
(if the temperature set has not yet been
reached) in the temperature display.
To activate Demo mode
^ Press the On/Off button.
^ Press the On/Off button and the
Temperature button at the same time
for approx. 5 seconds.
^ Press the On/Off button.
Demo mode has now been
deactivated.
The Menu symbol X and the Super
cool symbol ª will flash.
^ Press the Temperature button
repeatedly until the 3 °C area lights
up in the temperature display.
The Menu symbol X and the Super
cool symbol ª will flash.
^ Press the Super cool button.
Demo mode has now been activated.
The r symbol and the 7 °C area of the
temperature display will light up.
If Demo mode is activated and the
appliance is then switched off and
back on again, all areas of the
temperature display will light up for a
short time. Demo mode remains
activated.
33
Electrical connection
Electrical connection U.K.
Non-rewireable plugs (BS 1363)
All electrical work should be carried out The fuse cover must be re-fitted when
by a suitably qualified and competent changing the fuse, and if the fuse cover
person in strict accordance with current is lost, the plug must not be used until a
local and national safety regulations
(BS 7671 in the UK).
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
Connection should be made via a
suitable switched socket which is easily your local electrical supplier.
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
WARNING
(RCD).
THIS APPLIANCE MUST BE
EARTHED
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.
34
Installation
Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliance's energy
Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
consumption.
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
This appliance must not be installed
directly next to another refrigerator
or freezer.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.
Further information is available from
your dealer.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Climate range
The appliance is designed for use within
certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data plate
inside the appliance.
Climate range
Ambient room
temperature
SN
N
ST
T
+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to rise with
the risk of food deteriorating and going
off.
35
Installation
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation the
ventilation gaps must not be covered
over. The air inlet and outlet must not be
covered or blocked in any way. They
should be dusted on a regular basis.
Installation
^ Remove the cable clip from the back
of the appliance.
^ Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^ Carefully push the appliance into
position
^ with its back against the wall.
Aligning the appliance
^ To align the appliance, adjust the feet
using a suitable spanner.
36
Installation
Appliance dimensions
A
B
C
D
E
K 12421 SD
1447 mm
600 mm
631 mm
1176 mm
646 mm
37
Changing the door hinging
The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
The hinge parts (hinge plate and
hinge pin) must be screwed
sufficiently tightly as otherwise the
appliance door could fall off. Danger
of injury. Also the door may not
close fully, which would prevent the
appliance from cooling down
properly. Take care to secure the
hinge plate and pin tightly. Check
all screws and tighten them if
necessary.
You will need the following tools:
– A Torx® 15 and a Torx® 25
screwdriver,
– a flat-bladed screwdriver,
– a spanner (supplied).
Two people are needed for
changing the door hinging.
Changing over the door
Removing the door handle
Caution. The door is not secure as
soon as the hinge pin is removed.
^ With the help of another person, tip
the appliance back slightly.
^ Pull door handle a towards you. Side
section b slides back.
^ Pull side section b firmly back out of
the guides on the mounting plate.
^ Unscrew retaining screw c on
bottom right hinge plate d.
^ Undo the 4 screws (Torx® 15) in the
mounting plate, and remove the
handle.
^ Remove the cover caps from the
opposite side, and fit them into the
empty holes.
38
Changing the door hinging
^ Pull out spacer pin p from beneath
the left-hand side of the door.
^ Undo screws f and take hinge plate
d off.
^ Open the door.
^ Undo the screw of hinge part g on
hinge plate d slightly. Fit it into the
hole opposite in hinge plate d and
tighten up the screw.
^ Holding the door at the bottom and
on the handle side, carefully lift it
upwards and off.
This will release hinge pin e with
washer o from hinge plate d. If it
does not release:
^ Remove plug h and place it in the
opposite hole in the hinge plate.
^ Remove cover i.
^ Press hinge pin e with washer o out
of the hinge plate from below.
^ Unscrew and remove screw j and
refit it into the outer hole of the
opposite side.
^ Turn cover i through 180°, and fit it
into the holes on the other side.
^ Screw hinge plate d into position on
the opposite side using the two outer
long slots only. Do not use the middle
hole because you will not be able to
align the door later on.
39
Changing the door hinging
^ Using a screwdriver, remove spring
clamp n from underneath the door
and fit it on the opposite side.
^ Pull hinge pin e with washer o out
of the door bearing bush from below.
Important. The opening on washer
o must be placed over the tab on
hinge pin e so that washer o sits
correctly on hinge pin e.
^ Unscrew upper hinge pin k using a
suitable spanner.
^ Using a flat-bladed screwdriver
remove covers l from the front.
^ Place hinge pin e with washer o in
the door bearing bush on the
opposite side. Important. The tab on
the pin must face the inside of the
door and the notch the outside.
^ Screw in upper hinge pin k on the
opposite side using a suitable
spanner.
^ Refit covers l from the back on the
opposite side, and then click them
into place at the front.
^ Remove caps m from the door
bearing bush in the door and refit on
the opposite side.
40
Changing the door hinging
^ Take the door and guide the upper
door bearing bush onto upper hinge
pin k.
Refitting the handle
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^ Pivot the door and place hinge pin e
into hinge plate d. Important. Turn
the hinge pin if necessary, so that the
tab is pointing to the inside of the
door and the notch to the outside.
The hinge pin will then click into
place.
^ Loosely attach the handle to the
opposite side of the door with the two
front screws b.
^ With the help of another person,
carefully tip the appliance back and
tighten retaining screw c. Tighten it
using a suitable spanner.
Mounting plate c must be positioned
on the side of the door so that when the
door is closed it is flush with the side of
the appliance.
^ Align the door with the appliance
housing again if necessary using the
long slots in the lower hinge plate.
Then tighten the screws.
If this is not the case,
^ tighten both grub screws a with a
suitable allen key until mounting plate
c lines up correctly.
^ Replace spacer pin p underneath
the right-hand side of the door.
^ Then tighten all 4 screws b.
^ Slide the side section of handle d
into the guides on the mounting plate
until it clicks into place.
41
Changing the door hinging
It is important to check that the side
section of handle d does not come
into contact with the door seal when
opening the door, as this would
damage the door seal permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^ Realign mounting plate c with grub
screws a until the mounting plate
and the side section of handle d are
at the correct angle and the side
section does not touch the door seal
when the door is opened.
42
Aligning the appliance door
The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be used again.
43
Building in the appliance
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installed next to a wall d a
distance of approx. 55 mm must be
maintained on the hinge side between
the wall d and the appliance b, so
that the doors and the handles have
sufficient space for opening.
aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box a.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm2 to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
44
45
46
47
Alteration rights reserved / 4811
K 12421 SD
M.-Nr. 09 290 820 / 00
|